View XMLBWT-00-0000-000BT60E3_8882586.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

cld-ds61 rev 6f cree ? xlamp ? xm-l2 leds pro duc t d escrip tion the xlamp ? xm-l2 l e d builds on the unprecedented performance of the original xm-l, increasing lumen output up to 20% while providing a single die le d point source for precise optical control. the xm-l2 l e d shares the same mechanical and optical footprint as the original xm-l, providing a seamless upgrade path and shortened design cycle. xlamp xm-l2 l e ds are the ideal choice for lighting applications where high light output and maximum effcacy are required, such as l e d light bulbs, outdoor lighting, portable lighting, indoor lighting and solar-powered lighting. fea tures ? available in white, 70 -cri white, 80-cri white, 85-cri white and 90-cri white ? ansi- compatible chromaticity bins ? binned at 85?c ? maximum drive current: 3000?ma ? low thermal resistance: 2.5?c/w ? wide viewing angle: 125 ? unlimited foor life at 30?oc/85% rh ? refow solderable - jedec j-std-020c ? e lectrically neutral thermal path ? rohs and reach compliant ? ul ? recognized component (e349212) ta ble o f cont e nts characteristics ........................................ 2 flux characteristics ................................ 3 relative spectral power distribution ..... 5 relative flux vs. junction temperature . 5 e lectrical characteristics ........................ 6 relative flux vs. current ......................... 6 relative chromaticity vs. current ........... 7 relative chromaticity vs. temperature .. 7 typical spatial distribution ..................... 8 thermal design ....................................... 8 refow soldering characteristics ........... 9 notes ..................................................... 10 mechanical dimensions ....................... 12 tape and reel ........................................ 13 packaging .............................................. 14 product family data sheet copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. cree, inc. 4600 silicon drive durham, nc 27703 usa tel: +1.919.313.5300 www. cr ee. c om/x lamp
2 ch ar ac teristics characteristics unit minimum t ypical maximum thermal resistance, junction to solder point c/w 2.5 viewing angle (fwhm) degrees 125 temperature coeffcient of voltage mv/c -1.6 esd withstand voltage (hbm per mil-std-883d) v 8000 dc forward current ma 3000 reverse voltage v -5 forward voltage (@ 700?ma, 85?c) v 2.85 3.15 forward voltage (@ 1500?ma, 85?c) v 3.05 forward voltage (@ 3000?ma, 85?c) v 3.3 le d junction temperature c 150 copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
3 notes: ? cree maintains a tolerance of 7% on fux and power measurements, 0.005 on chromaticity (ccx, ccy) measurements and 2 on cri measurements. see the measurements section (page 10). ? typical cri for cool white (5000 k C 8300 k cct) is 65. ? minimum cri for 70-cri white is 70. ? typical cri for neutral white (3700 k C 5000 k cct) is 75. ? minimum cri for 80-cri white is 80. ? typical cri for warm white (2600 k C 3700 k cct) is 80. ? minimum cri for 85-cri white is 85. ? minimum cri for 90-cri white is 90. * flux values @ 25?c are calculated and are for reference only. ** calculated fux values at 1000?ma, 1500?ma and 2000?ma are for reference only. fl ux ch ar ac teristic s ( t j = 85?c) the following table provides several base order codes for xlamp xm-l2 l e ds. it is important to note that the base order codes listed here are a subset of the total available order codes for the product family. for more order codes, as well as a complete description of the order-code nomenclature, please consult the xlamp xm l e d family binning and labeling document. color cc t range minimum luminous flux (lm) @ 700?ma calculated minimum luminous flux (lm) @ 85?c** o rder code min. max. group flux (lm) @ 85?c flux (lm) @ 25?c* 1000 ma 1500 ma 2000 ma cool white 5000 k 8300 k t5 260 296 357 502 631 xmlbwt-00-0000-0000t5051 t6 280 318 385 541 679 xmlbwt-00-0000-0000t6051 u2 300 342 412 580 728 xmlbwt-00-0000-0000u2051 u3 320 364 439 618 776 xmlbwt-00-0000-0000u3051 neutral white 3700 k 5000 k t4 240 273 330 464 582 xmlbwt-00-0000-000lt40e4 t5 260 296 357 502 631 xmlbwt-00-0000-000lt50e4 t6 280 318 385 541 679 xmlbwt-00-0000-000lt60e4 u2 300 342 412 580 728 xmlbwt-00-0000-000lu20e4 warm white 2600 k 3700 k t2 200 227 275 386 485 xmlbwt-00-0000-000lt20e7 t3 220 250 302 425 534 xmlbwt-00-0000-000lt30e7 t4 240 273 330 464 582 xmlbwt-00-0000-000lt40e7 t5 260 296 357 502 631 xmlbwt-00-0000-000lt50e7 70-cri white 3700 k 5000 k t5 260 296 357 502 631 xmlbwt-00-0000-000bt50e3 t6 280 318 385 541 679 XMLBWT-00-0000-000BT60E3 u2 300 342 412 580 728 xmlbwt-00-0000-000bu20e3 u3 320 364 439 618 776 xmlbwt-00-0000-000bu30e3 80-cri white 2600 k 4300 k t2 200 227 275 386 485 xmlbwt-00-0000-000ht20e7 t3 220 250 302 425 534 xmlbwt-00-0000-000ht30e7 t4 240 273 330 464 582 xmlbwt-00-0000-000ht40e7 t5 260 296 357 502 631 xmlbwt-00-0000-000ht50e7 85-cri white 2600 k 3200 k s4 164 186 225 317 398 xmlbwt-00-0000-000ps40e7 s5 172 196 236 332 417 xmlbwt-00-0000-000ps50e7 s6 182 207 250 352 442 xmlbwt-00-0000-000ps60e7 t2 200 227 275 386 485 xmlbwt-00-0000-000pt20e7 copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
4 notes: ? cree maintains a tolerance of 7% on fux and power measurements, 0.005 on chromaticity (ccx, ccy) measurements and 2 on cri measurements. see the measurements section (page 10). ? typical cri for cool white (5000 k C 8300 k cct) is 65. ? minimum cri for 70-cri white is 70. ? typical cri for neutral white (3700 k C 5000 k cct) is 75. ? minimum cri for 80-cri white is 80. ? typical cri for warm white (2600 k C 3700 k cct) is 80. ? minimum cri for 85-cri white is 85. ? minimum cri for 90-cri white is 90. * flux values @ 25?c are calculated and are for reference only. ** calculated fux values at 1000?ma, 1500?ma and 2000?ma are for reference only. color cc t range minimum luminous flux (lm) @ 700?ma calculated minimum luminous flux (lm) @ 85?c** o rder code min. max. group flux (lm) @ 85?c flux (lm) @ 25?c* 1000 ma 1500 ma 2000 ma 90-cri white 2600 k 3200 k s4 164 186 225 317 398 xmlbwt-00-0000-000us40e7 s5 172 196 236 332 417 xmlbwt-00-0000-000us50e7 s6 182 207 250 352 442 xmlbwt-00-0000-000us60e7 t2 200 227 275 386 485 xmlbwt-00-0000-000ut20e7 fl ux ch ar ac teristic s ( t j = 85?c) - continued copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
5 rela tive spec tral pow e r distribution rela tive fl ux vs. jun c tion tempera ture ( i f ?=?700? m a) relative spectral power 0 20 40 60 80 100 380 430 480 530 580 630 680 730 780 relative radiant power (%) wavelength (nm) 5000 k - 8300 k cct 3700 k - 5000 k cct 2600 k - 3700 k cct relative flux output vs. junction temperature 0 20 40 60 80 100 120 25 50 75 100 125 150 relative luminous flux (%) junction temperature (oc) copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
6 elec trical ch ar ac teristic s ( t j = 85?c) rela tive fl ux vs. curr e nt ( t j = 85?c) electrical characteristics (tj = 85c) 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 2.6 2.8 3.0 3.2 3.4 forward current (ma) forward voltage (v) relative intensity vs. current (tj = 85c) 0 50 100 150 200 250 300 350 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 relative luminous flux (%) forward current (ma) copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
7 re la tive ch ro ma tic ity vs. curr ent (w arm white) re la tive ch ro ma tic ity vs. tempera tur e (w arm white) relative chromaticity vs. current, ww - 0.012 - 0.008 - 0.004 0.000 0.004 0.008 0.012 0 500 1000 1500 2000 2500 3000 current (ma) ccx ccy relative chromaticity vs. temperature ww - 0.012 - 0.008 - 0.004 0.000 0.004 0.008 0.012 25 50 75 100 125 150 tsp ( c) ccx ccy copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
8 t ypical spa ti al distribution ther mal design the maximum forward current is determined by the thermal resistance between the l e d junction and ambient. it is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. typical spatial radiation pattern 0 20 40 60 80 100 - 90 - 70 - 50 - 30 - 10 10 30 50 70 90 relative luminous intensity (%) angle (o) thermal design cool white 0 500 1000 1500 2000 2500 3000 3500 0 20 40 60 80 100 120 140 160 maximum current (ma) ambient temperature (oc) rj - a = 4 c/w rj - a = 7 c/w rj - a = 10 c/w rj - a = 15 c/w copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
9 refl ow so ldering ch ar ac teristics in testing, cree has found xlamp xm-l2 leds to be compatible with jedec j -std- 020c, using the parameters listed below. as a general guideline, cree recommends that users follow the recommended soldering profle provided by the manufacturer of the solder paste used. note that this general guideline may not apply to all pcb designs and confgurations of refow soldering equipment. profile feature lead-free solder average ramp-up rate (ts max to tp) 1.2?c/second preheat: temperature min (ts min ) 120 c preheat: temperature max (ts max ) 170 c preheat: time (ts min to ts max ) 65-150 seconds time maintained above: temperature (t l ) 217 c time maintained above: time (t l ) 45-90 seconds peak/classifcation temperature (tp) 235 - 245 c time within 5?c of actual peak temperature (tp) 20-40 seconds ramp-down rate 1 - 6 c/second time 25?c to peak temperature 4 minutes max. note: all temperatures refer to the topside of the package, measured on the package body surface. ipc/jedec j-std-020c t p t l temperature time t 25?c to peak preheat ts t s t p 25 ramp-down ramp-up critical zone t l to t p ts max ts min copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
10 n otes measurements the luminous fux, radiant power, chromaticity and cri measurements in this document are binning specifcations only and solely represent product measurements as of the date of shipment. these measurements will change over time based on a number of factors that are not within crees control and are not intended or provided as operational specifcations for the products. calculated values are provided for informational purposes only and are not intended as specifcations. p re-release qualifcation t esting please read the le d reliability overview for details of the qualifcation process cree applies to ensure long-term reliability for xlamp leds and details of crees pre-release qualifcation testing for xlamp leds. lumen maintenance cree now uses standardized i e s lm-80-08 and tm-21-11 methods for collecting long-term data and extrapolating le d lumen maintenance. for information on the specifc lm - 80 data sets available for this led, refer to the public lm-80 results document . please read the long-term lumen maintenance application note for more details on crees lumen maintenance testing and forecasting. please read the thermal management application note for details on how thermal design, ambient temperature, and drive current affect the le d junction temperature. moisture sensitivity cree recommends keeping xlamp l e ds in the provided, resealable moisture-barrier packaging (mbp) until immediately prior to soldering. unopened mbps that contain xlamp le ds do not need special storage for moisture sensitivity. once the mbp is opened, xlamp xm-l2 leds may be stored as msl 1 per jedec j-std-033, meaning they have unlimited foor life in conditions of 30 oc/85% relative humidity (rh). regardless of the storage condition, cree recommends sealing any unsoldered leds in the original mbp. rohs compliance the levels of rohs restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eu directive 2011/65/ec (rohs2), as implemented january 2, 2013. rohs declarations for this product can be obtained from your cree representative or from the product documentation sections of www.cree.com . r each compliance reach substances of very high concern (svhcs) information is available for this product. since the european chemical agency (echa) has published notice of their intent to frequently revise the svhc listing for the foreseeable future, please contact a cree representative to insure you get the most up-to-date reach svhc declaration. reach banned substance information (reach article 67) is also available upon request. copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
11 ul ? r ecognized component level 4 enclosure consideration. the led package or a portion thereof has been investigated as a fre and electrical enclosure per ansi/ ul 8750. v ision advisory warning: do not look at exposed lamp in operation. eye injury can result. for more information about l e ds and eye safety, please refer to the led e ye safety application note . n ote s - continued copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
12 mech anical dimensions thermal vias, if present, are not shown on these drawings. all measurements are .13 mm unless otherwise indicated. t op view b ottom view side view recommended pcb s older pad recommended s tencil pattern (s haded area is open) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 5.00 5.00 r 2.26 3.02 0.73 .50 3.78 2.78 4.78 4.78 .50 4.78 .80 .50 .25 .80 .25 .97 4.78 .50 .50 2.78 4.78 4.78 1 / 1 16.000 b 2610-00032 outline drawing, 5050 xmlb -- -- -- -- -- -- 11/14/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) all dimensions are .13mm unless otherwise noted size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 5.00 5.00 r 2.26 3.02 0.73 .50 3.78 2.78 4.78 4.78 .50 4.78 .80 .50 .25 .80 .25 .97 4.78 .50 .50 2.78 4.78 4.78 1 / 1 16.000 b 2610-00032 outline drawing, 5050 xmlb -- -- -- -- -- -- 11/14/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) all dimensions are .13mm unless otherwise noted copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
13 tape and reel all cree carrier tapes conform to eia-481d, automated component handling systems standard. e xcept as noted, all dimensions in mm. size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection x .5 .xxx .010 .xx .03 .x .06 for sheet metal parts only .xx .01 .xxx .005 x .5 unless otherwise specified dimensions are in inches and after finish. tolerance unless specified: scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contaned within are the proprietary and cree confidential. this plot and the information of cree inc. notice surface finish: 63 330 +.25 -.75 12.4 +1.0 -.5 measured at edge 16.4 +0.2 .0 measured at hub 12.4 +.2 .0 measured at hub .2 13.1 1.9.4 .4 21 60 60 1 / 1 0.500 a 2400-00009 reel, 13" x 12mm, 3 piece snap - anti-static hips -- -- -- -- 09/29/09 d. cronin 2400-00009 index qty item comments 1 1 2400-00009-core 2 2 2400-00009-reel revisons rev description by date app'd size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) loaded pockets (1000 lamps) leader 400mm (min.) of empty pockets with at least 100mm sealed by tape (40 empty pockets min.) 12 1.75 4 8 3.35 1 / 1 3.000 b 2402-00012 xm loading spec -- -- -- -- -- -- 06/08/10 d. cronin revisons rev description by date app'd a loaded pocket count was 750 dds 11/8/10 bs b made cathode and anode note larger dc 2/26/12 end start user feed direction cathode side anode side 1 2 3 4 6 5 d c b a app'd date by revisions rev description size title of rev. sheet a drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 4600 silicon drive fax (919) 313-5558 durham, n.c 27703 phone (919) 313-5300 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .010 .xx .03 .x .06 for sheet metal parts only .xx .01 .xxx .005 x .5 unless otherwise specified dimensions are in inches and after finish. tolerance unless specified: surface finish: 63 1 / 1 drawing scale a 2402-00011 xm 5050 carrier tape 4/23/10 d. cronin cree reference drawing for tek-pak drawing 018275 .36[.014] t 5.40[.213] ao 3.35[.132] ko 3.0 5.40[.213] bo 2.00[.079] p2 4.00[.157] po do1.50 +.10 -.00 .0591 +.0039 -.0000 [ ] 10.25 [.404] e2 7.0 12.00[.472] nominal 12.30 [.484] max w 1.75[.069] e1 5.50[.217]f 1.50[.059] d1 8.00[.315] p pocket size ao - 5.40mm [.213"] bo - 5.40mm [.213"] ko - 3.35mm [.132"] 1 2 3 4 6 5 d c b a app'd date by revisions rev description size title of rev. sheet a drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 4600 silicon drive fax (919) 313-5558 durham, n.c 27703 phone (919) 313-5300 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .010 .xx .03 .x .06 for sheet metal parts only .xx .01 .xxx .005 x .5 unless otherwise specified dimensions are in inches and after finish. tolerance unless specified: surface finish: 63 1 / 1 drawing scale a 2402-00011 xm 5050 carrier tape 4/23/10 d. cronin cree reference drawing for tek-pak drawing 018275 .36[.014] t 5.40[.213] ao 3.35[.132] ko 3.0 5.40[.213] bo 2.00[.079] p2 4.00[.157] po do1.50 +.10 -.00 .0591 +.0039 -.0000 [ ] 10.25 [.404] e2 7.0 12.00[.472] nominal 12.30 [.484] max w 1.75[.069] e1 5.50[.217]f 1.50[.059] d1 8.00[.315] p pocket size ao - 5.40mm [.213"] bo - 5.40mm [.213"] ko - 3.35mm [.132"] 1 2 3 4 6 5 d c b a app'd date by revisions rev description size title of rev. sheet a drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 4600 silicon drive fax (919) 313-5558 durham, n.c 27703 phone (919) 313-5300 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .010 .xx .03 .x .06 for sheet metal parts only .xx .01 .xxx .005 x .5 unless otherwise specified dimensions are in inches and after finish. tolerance unless specified: surface finish: 63 1 / 1 drawing scale a 2402-00011 xm 5050 carrier tape 4/23/10 d. cronin cree reference drawing for tek-pak drawing 018275 .36[.014] t 5.40[.213] ao 3.35[.132] ko 3.0 5.40[.213] bo 2.00[.079] p2 4.00[.157] po do1.50 +.10 -.00 .0591 +.0039 -.0000 [ ] 10.25 [.404] e2 7.0 12.00[.472] nominal 12.30 [.484] max w 1.75[.069] e1 5.50[.217]f 1.50[.059] d1 8.00[.315] p pocket size ao - 5.40mm [.213"] bo - 5.40mm [.213"] ko - 3.35mm [.132"] copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led
14 p ac k aging label with cree bin code, qty, lot # label with cree bin code, qty, lot # vacuum-sealed moisture barrier bag dessicant (inside bag) humidity indicator card (inside bag) patent label label with customer order code, qty, reel id, po # patent label label with cree bin code, quantity, reel id label with cree bin code, quantity, reel id label with cree order code, quantity, reel id, po # label with cree order code, quantity, reel id, po # label with cree bin code, quantity, reel id unpackaged reel packaged reel boxed reel copyright ? 2012-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? x m -l2 led

▲Up To Search▲

Price & Availability of XMLBWT-00-0000-000BT60E3

	To Download XMLBWT-00-0000-000BT60E3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .